7*24 all day long
zhengzhou,china
[email protected]
7*24 all day longzhengzhou,china[email protected]Aggregate Crushing Strength Test. Aggregate Crushing Value Calculator, Test on course and . is 2386-4 1963 methods of test for aggregates for concrete part 4 . 1.1 this standard part iv covers the following tests for aggregates for concrete of crushing strength. 2. aggregate crushing value of coarse aggregate
Get Price
Aggregate used in road construction, should be strong enough to resist crushing under traffic wheel loads. If the aggregates are weak the stability of the pavement structure is likely to be adversely affected. The strength of coarse aggregates is assessed by aggregate crushing test
→
aggregate crushing value of coarse aggregate. NOTE 1 -The ‘aggregate crushing value’ gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre- gate of ‘aggregate crushing value’ 30 or higher, the result may be anomalous, and in
→
Aug 22, 2021 i. Crushing Value. The crushing value gives the resistance of a coarse aggregate to crushing under the application of compressive load. j. Deleterious Materials. Coarse aggregate should be free from deleterious materials such as clay, silt, dust, salt contamination, organic materials, etc. because these materials weaken the bond. k. Surface Water
→
The strength of coarse aggregates is assessed by aggregates crushing test. The aggregate crushing value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement, aggregate possessing low aggregate crushing value
→
2.1.2 Crushed Stone Sand - Fine aggregate produced by crushing hard stone. 2.1.3 Crushed Grace1 Sand - line aggregate produced by crushing natural gravel. . 2.2 Coarse Aggregate -- Aggregate most of which is retained on 4*75-mm IS Sieve and containing only so much finer material as is permitted for
→
Note 1: A procedure for testing coarse aggregate larger than 19.0 mm [3 / 4 in.] is covered in Test Method C535. Thus coarse aggregates with a maximum size between 19 mm [3 / 4 in.] and 37.5 mm [1 1 / 2 in.] may be tested by Test Method C535 or Test Method C131/C131M
→
Then crushed aggregates are then sieved through 2.36 mm sieve and weight of passing material is expressed as percentage of the weight of the total sample which is the aggregate crushing value. A value less than 10 signifies an exceptionally strong aggregate while above 35 would normally be regarded as weak aggregates
→
Values of 22.8%, 28.2% and 4.4% were obtained for aggregate crushing value, aggregate impact value and aggregate water absorption respectively. The concrete mixes were prepared using crushed over burnt bricks as coarse aggregates at water – cement ratios of 0.40, 0.50, 0.55 and 0.60
→
Aggregate used in road construction, should be strong enough to resist crushing under traffic wheel loads. If the aggregates are weak the stability of the pavement structure is likely to be adversely affected. The strength of coarse aggregates is assessed by aggregate crushing test
→
Methods of test for aggregates for concrete 3.81 Мб. 2.1 Object aggregate This method of test covers the procedure crushing value of coarse aggregate. for determining ‘aggregate crushing value’ gives a relativeAll dimensions in millimetres. FIG. 3 Los ANGELES NOTE 2 -Suggested ABRASION TESTING MACHINE b) Sieves- The I-70-mm IS Sieve
→
Aggregate Crushing Value. AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) – 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes – 12.5mm, 10mm and 2.36mm. Procedure to determine Aggregate Crushing Value
→Copyright © 2020.Henan Exodus Machinery Co., ltd. All rights reserved. Sitemap
